Owl face: Amigurumi Face Placement Planner

Large eye outlines with separate brows

The owl study has a thirty-six-position, fourteen-round reference, with eyes at stitches thirteen and twenty-three on round seven. Its eye outlines are wider than the frog's: half-width 1.1 stitch intervals and half-height 0.7 rounds. Smaller dark eyes remain centered within them. The two centers are ten intervals apart, leaving nine numbered positions strictly between. Establish the front center at stitch eighteen before transferring the brow landmarks.

Count the angular brow vertices

The left brow goes from stitch twelve on round 6.4 to thirteen on round 6.1, then to 13.9 on round 6.45. The right brow mirrors it: 22.1 on round 6.45, twenty-three on round 6.1 and twenty-four on round 6.4. These are open, angular backstitched lines, not smooth quadratic curves. The unequal decimal offsets preserve the intended mirrored silhouette. Do not connect them across the center or turn the brow line into another head round.

Let the beak supply the lower focal point

The gold diamond beak starts at stitch eighteen on round 7.6, reaches 18.65 on round eight, drops to eighteen on round 8.5 and returns through 17.35 on round eight. Close to the first point. No mouth is added below it. The same gold slot outlines the eye rings, so the saved palette ties those elements together. A differently colored facial disk or a sewn beak would be another design, with its own material and attachment requirements.

Questions and common mistakes

Do the eyebrows mark increases?

No. Every displayed feature is embroidery placed on an already counted head. The head reference stays thirty-six positions around the featured band.

Why is one eye visually smaller?

Compare both outer-ring radii and the tension of the couching or outlining stitches. Equal center spacing cannot compensate for a compressed embroidered outline.

Can I copy the beak positions from another head width?

Regenerate using the actual counted width first. The center changes with circumference, and the original coordinates belong specifically to this thirty-six-position reference.

Exact setup, compatible head reference and finishing

Open the Amigurumi Face Placement Planner and choose owl, circumference 36, height 14 and eye separation 10. The reference below assumes an existing single-crochet head with six stitches in a magic ring, then six evenly distributed increases on each round until 36 stitches. Work three even rounds, then six evenly distributed decreases per round until six remain; close those final loops with the tail. This optional arithmetic reference has 14 worked rounds. Its maximum-count band provides a reference for the eye line and nearby feature anchors. Fractional curve controls are guide locations; check their position on the actual curved surface rather than assuming every referenced level has the maximum circumference. Swatch and finish a physical head before assessing the actual fit.

The placement tool generates embroidery instructions, not that head construction. Use a tapestry needle and suitable contrasting yarn, transfer temporary landmarks, then follow the complete paths below. Round coordinates increase downward on this unwrapped face map. Fractional locations lie between markers. Short backstitches follow straight paths; curved strands are couched to the drawn guide. Secure each separate tail inside without pulling the surface inward. Review the chart-reading guide and keep the exact project JSON with your chosen trial. US and UK modes retain the same coordinates. No physical crochet or toy certification is implied by the calculated example.

1. owl placement trial on an existing head: mark front center stitch 18. Eyes are centered at stitches 13 and 23 on round 7; separation 10 stitch intervals (9 numbered positions strictly between). left-eye-ring: embroider an oval centered at (13, R7), half-width 1.1 stitch intervals and half-height 0.7 rounds; yarn slot 3. left-eye: embroider an oval centered at (13, R7), half-width 0.35 stitch intervals and half-height 0.35 rounds; yarn slot 2. right-eye-ring: embroider an oval centered at (23, R7), half-width 1.1 stitch intervals and half-height 0.7 rounds; yarn slot 3. right-eye: embroider an oval centered at (23, R7), half-width 0.35 stitch intervals and half-height 0.35 rounds; yarn slot 2. beak: backstitch (18, R7.6) → (18.65, R8) → (18, R8.5) → (17.35, R8), close to the first point; yarn slot 3. left-brow: backstitch (12, R6.4) → (13, R6.1) → (13.9, R6.45); yarn slot 2. right-brow: backstitch (22.1, R6.45) → (23, R6.1) → (24, R6.4); yarn slot 2. Fractional coordinates are between stitch or round markers; curve controls guide the shape and are not extra insertion points. Compare temporary threads on the stuffed head, then secure each separate strand inside without distorting the surface. This plan references 36 head positions; it does not make 36 new crochet stitches. [36 existing head reference positions]