Penguin face: Amigurumi Face Placement Planner

Separate eye-patch outlines from the pupils

This thirty-six-position, fourteen-round study uses a pale head reference, dark eye marks and a gold accent. The eyes are centered at stitches fourteen and twenty-two on round seven, equally spaced around center stitch eighteen. Each patch outline has half-width 0.85 stitch intervals and half-height 0.8 rounds. Inside it, a smaller dark oval has half-width and half-height 0.35. These are two separate embroidery outlines at each eye, not crocheted appliques or a generated white belly panel.

Place the beak on the center line

The beak has four ordered corners: position eighteen on round 7.6, position 18.65 on round eight, position eighteen on round 8.5 and position 17.35 on round eight. Close the last edge back to the upper point. This gold diamond is the only central lower feature in the saved plan. There is no additional smile, nose line or split muzzle. Adding one would change the intended expression rather than complete a missing generated step.

Check contrast without changing the coordinate budget

The chosen accent colors both the larger eye outlines and the beak; the second yarn slot colors the smaller eyes. Test that combination on the actual yarn before securing embroidery. The digital head tint is deliberately faint so reference marks remain visible, and does not predict the contrast of the finished stuffed surface. If a different patch color is needed, save a revised palette and compare it at the same coordinates before making any permanent marks.

FAQ and likely mistakes

Does the gold outline represent a separate felt beak?

No. It is an embroidered closed path. A felt component would need its own material choice, seam and attachment assessment.

Why is there no mouth below it?

The diamond itself supplies the bird's beak. The generator intentionally omits the mammal mouth primitives in this study.

What if I enter only two yarn colors?

The accent falls back to the feature slot. Geometry stays the same, but the outlined patches and beak share that yarn. The downloadable example preserves its three-slot choice for a reproducible comparison.

Exact setup, compatible head reference and finishing

Open the Amigurumi Face Placement Planner and choose penguin, circumference 36, height 14 and eye separation 8. The reference below assumes an existing single-crochet head with six stitches in a magic ring, then six evenly distributed increases on each round until 36 stitches. Work three even rounds, then six evenly distributed decreases per round until six remain; close those final loops with the tail. This optional arithmetic reference has 14 worked rounds. Its maximum-count band provides a reference for the eye line and nearby feature anchors. Fractional curve controls are guide locations; check their position on the actual curved surface rather than assuming every referenced level has the maximum circumference. Swatch and finish a physical head before assessing the actual fit.

The placement tool generates embroidery instructions, not that head construction. Use a tapestry needle and suitable contrasting yarn, transfer temporary landmarks, then follow the complete paths below. Round coordinates increase downward on this unwrapped face map. Fractional locations lie between markers. Short backstitches follow straight paths; curved strands are couched to the drawn guide. Secure each separate tail inside without pulling the surface inward. Review the chart-reading guide and keep the exact project JSON with your chosen trial. US and UK modes retain the same coordinates. No physical crochet or toy certification is implied by the calculated example.

1. penguin placement trial on an existing head: mark front center stitch 18. Eyes are centered at stitches 14 and 22 on round 7; separation 8 stitch intervals (7 numbered positions strictly between). left-eye-ring: embroider an oval centered at (14, R7), half-width 0.85 stitch intervals and half-height 0.8 rounds; yarn slot 3. left-eye: embroider an oval centered at (14, R7), half-width 0.35 stitch intervals and half-height 0.35 rounds; yarn slot 2. right-eye-ring: embroider an oval centered at (22, R7), half-width 0.85 stitch intervals and half-height 0.8 rounds; yarn slot 3. right-eye: embroider an oval centered at (22, R7), half-width 0.35 stitch intervals and half-height 0.35 rounds; yarn slot 2. beak: backstitch (18, R7.6) → (18.65, R8) → (18, R8.5) → (17.35, R8), close to the first point; yarn slot 3. Fractional coordinates are between stitch or round markers; curve controls guide the shape and are not extra insertion points. Compare temporary threads on the stuffed head, then secure each separate strand inside without distorting the surface. This plan references 36 head positions; it does not make 36 new crochet stitches. [36 existing head reference positions]